Miscellaneous

Sold per Pair... The innovative BX1 squeezes the performance of a much larger speaker into a format that's easy to enjoy anywhere in the home. A wider more consistent frequency response from its C-CAM® drivers will give you the fidelity and bandwidth you'll need to liberate the essence of your music and film favourites while leaving the choice of installation options wide open. The two-way BX1 utilises a single 140mm (5 1/2") C-CAM® bass driver and 25mm (1") C-CAM® tweeter in a system designed to defy the usual size/performance assumptions. New C-CAM® tweeter has greater sensitivity and a wider bandwidth beyond 30kHz. New C-CAM® bass and mid-range drivers refined by FEA analysis. Single bolt-through drivers. A design feature which means the driver is not fixed to the front baffle and cannot transmit vibrations and therefore colouration to the cabinet. Improved cabinet rigidity and stability. HiVe®II port technology to speed the transit of air from the cabinet resulting in more dynamic bass. High-quality terminal panels blend easy access with high-end functionality. Choice of four high quality vinyl wood finishes. Frequency Response +/- 3dB: 55Hz - 30kHz Sensitivity (1W@1m): 88 dB Nominal Impedance:8 ohms Power Handling (RMS):70 W Recommended Amplifier Requirements (RMS):15 - 70 W Cabinet Design: Rear ported bass reflex. HiVe®II port technology Crossover Frequency: 3.2 kHz Drive Unit Complement: 1 x 140mm (5 1/2") C-CAM® bass mid-range driver. 1 x 25mm (1") gold dome C-CAM® tweeter External Dimensions: (H x W x D) 260 x 165 x 180 mm 10 1/4 x 6 1/2 x 7 1/16 inches Weight (Individual): 3.86 Kg (8.5 lb)

Vox teamed up with renowned tube amp designer Tony Bruno to produce the TB18C1, a tube combo amplifier with an American accent. The 18-watt, 1 x 12" TB18C1 puts a duo of 6V6 power tubes (plus two 12AX7 preamp tubes) to work, giving you a big-sounding amp that's equally at home in the studio and onstage. You'll love how this amp reacts to your playing; you get that magical range of clean-to-breakup tones, accessible right from your guitar's volume knob. The TB18C1 also includes a Mid Boost mode that boosts mids and overall gain. Perfect for solos! A bass boost and tube-powered reverb are also onboard. Want to take the Vox TB18C1 combo amp to the limit? Just bypass the master volume and crank it up.Vox TB18C1 Combo Amplifier at a Glance:Designed by amp guru Tony BrunoMid Boost for attention-grabbing solosDark switch doubles your tonal optionsDesigned by amp guru Tony BrunoTony Bruno is a boutique amp designer with a reputation for building some of the best-sounding amps in the world. Vox has collaborated with Tony in the past, on such amps as the 2002 hand-wired AC30 as well as the acclaimed Night Train amplifier. The TB18C1 is the result of an original circuit design Tony created for Vox. Combining Vox's decades of experience and Tony's innovative circuit design makes the TB18C1 a boutique-quality amp at a down-to-earth price. Mid Boost for attention-grabbing solosThe TB18C1 combo sports a Mid Boost switch to boost the gain of your midrange frequencies, perfect for adding some backbone to your solos and leads. Or simply leave the Mid Boost engaged, changing the tonality and response of the TB18C1 and giving you whole new tones to explore.Dark switch doubles your tonal optionsfurthering the tonal diversity of the TB18C1, Tony Bruno included a Dark switch that radically changes the sound of this combo. The Dark switch rolls off high frequencies drastically, giving a whole new sound and vibe to the TB18C1. Combining the Dark switch with the versatile Mid Boost switch as well as the on-board tone and reverb controls effectively gives you double the tonal territory you can cover with this combo.Vox TB18C1 Combo Amplifier Features:Single-channel tube combo amp, with circuit designed by boutique amplifier builder Tony BrunoVintage American tube voicingMid Boost mode gives you extra volume and bite for solos and leadsDark switch rolls off high frequencies, radically altering the sound and response of the comboMaster Volume bypass switch lets you push this amp to the limitsBirch-ply cabinet construction is ultra-durable and helps maintain a balanced, focused toneOne 12" Celestion G12-65 speaker, chosen for its classic tone and breakup characteristicsCustom-made premium transformersPlug into an American-voiced Vox!

Model Platinum-70A-HV-PRO Manual User Manual Preview Platinum-70A-HV-PRO ESC belongs to Hobbywing's "Platinum" series products line, it is the most significant top-class product for aircraft and helicopter. 1 Typical Applications 1.1 Very powerful for 600 class helicopter (Working with 8 or 10 cells Lipo battery) 1.2 Very powerful for huge scale aircraft such as F3A 2 Specification 2.1 Output: Continuous 70A, burst 105A up to 10 seconds. 2.2 Input Voltage: 5-12 cells lithium battery or 15-36 cells NIMH battery. 2.3 BEC: None. 2.4 Control Signal Transmission: Optically coupled system. 2.5 Max Speed: 210, 000rpm for 2 Poles BLM, 70, 000rpm for 6 poles BLM, 35, 000rpm for 12 poles BLM. (BLM: BrushLess Motor) 2.6 Size: 70mm (L) * 34mm (W) * 16mm (H). 2.7 Weight: 82g. 3 Features 3.1 High performance microprocessor brings out the best compatibility with all kinds of motors and the highest driving efficiency. 3.2 Wide-open heat-sink design to get the best heat dissipation effect. 3.3 With 3 types of start mode: Normal / Soft / Very-Soft, compatible with aircraft and helicopter. 3.4 Smooth, linear, quick and precise throttle response. 3.5 The throttle signal is transfered through optically coupled system to avoid the electromagnetic interference. 3.6 Multiple protection features: Low-voltage cut-off protection / Over-heat protection / Throttle signal loss protection. 3.7 Perfect governor mode for helicopter. 3.8 The firmware of the ESC can be updated through the USB adapter on the Professional LCD Program Box. 3.9 User programmable. Several kinds of program methods are supported: transmitter, digital LED program card, advanced professional LCD program box, PC software. Very easy to program the ESC at home or at the flying field.

Call Toll Free 1-866-513-5799, Mon-Fri 8-9, Sat and Sun 10-5 EST About Us Product Details Store Policy More In Portable Audio Headphones Kart-a-Bag Top and Bottom Shelves A275C OUR SKU# KN1310 MPN: A275C Condition Brand New Shipping Free Shipping Leaves warehouse within 24 to 48 hours With a transit time of 1-5 business days Standard Ground (e.g. UPS, FedEx). Please note that this product cannot be shipped to Alaska, Hawaii, or Puerto Rico. We apologize for the inconvenience. Click here to read

Single 6.0 Gallon Coffee Brewer Single brewer and 1 On-The-Go mobile LUXUS® dispenser. FETCO® is committed to designing equipment that is operator-friendly to increase safety, minimize training and increase productivity. Case and point, our Series 7000 large capacity brew basket drawer easily slides out so that the brew basket can be safely lifted in and out. Electrical: 120/208 Volts 22.7 Kilowatts 64.3 Amps: Dimensions:18-1/2W x 35D x 79H --261lbs: #Mfg C71028a Airpots sold separately.

Get your mixes to translate! The JBL MSC1 is a powerful heart to your monitoring system. Yes, it's a monitor controller, giving you easy switching between two sets of studio monitors — but it's much more than that! Included with the MSC1, you get a measurement microphone and JBL's Room Mode Correction technology. That way, you can compensate for acoustics problems in your room, so your mixes will always translate! The MSC1 works with all studio monitors, in any room. Plus, it features A/B/C input selection, for total pro monitoring control with the MSC1.JBL MSC1 Monitor System Controller at a Glance:Central Control for Your SystemJBL RMC TechnologyControl 3 Stereo InputsCentral Control for Your SystemCommand all control room monitoring functions right from your mix position, with the MSC1 Monitor System Controller. In a convenient desk-top form-factor, the MSC1 provides essential "monitor strip" features found in large mixing consoles. Since the acoustics of your room can play a big part in what you hear, the MSC1 includes JBL's highly acclaimed RMC Room Mode Correction Technology. The end-result is a calibrated reference environment in which your speakers work in harmony with your room to take the guesswork out of mixing. With RMC you can tune your monitor system for greater clarity at the mix position. With the MSC1, you're clearly in control.JBL RMC TechnologyIn the quest to deliver better mixes in any room, JBL developed RMC technology for their acclaimed LSR Series studio monitors. But they didn't stop there. They designed the MSC1 with next generation RMC to work with any studio monitor system in any room. No matter what speaker system you own, you can have a truly calibrated environment fine-tuned to give you your best mixes. The MSC1 includes JBL's acclaimed RMC Room Mode Correction technology that measures your room and tackles low frequency problems caused by room modes and boundary conditions. The MSC1 comes with everything needed to calibrate your system including a Calibration Mic, MSC1 Control Center Software, and accessory cables. Calibration is simply carried out using the supplied microphone, MSC1 Control Center Software and your computer. Before measuring your room, Control Center meticulously measures the signal path of your audio system to set the stage for an accurate speaker calibration. Control Center Software guides you through every step. Once your system has been measured, re-calibration of your speakers is fast and easy and can be done at any time. After RMC calibration, the MSC1 works as a stand-alone controller and connection to a computer is not required.Control 3 Stereo InputsAs the "hub" of your system, the MSC1 controls the monitoring of three stereo input sources such as a computer workstation, mixing console, electronic musical instrument, CD or personal MP3 player. The MSC1's primary speaker "A" outputs include a level control, monitor EQ and RMC Room Mode Correction to tune the monitors to the room. Selecting the "B" outputs assigns the volume control and input routing to a second set of speakers. Subwoofer controls let you add a sub to the "A" speaker system, with a dedicated level control, and a choice of bass management crossover settings. The MSC1 headphone output and independent level control let you send a headphone feed to a performer or monitor using headphones in the control room.JBL MSC1 Monitor System Controller Features:Master Volume ControlA/B Speaker SelectA/B/C input Source SelectSubwoofer Output with Level and Selectable Crossover FreqAdjustable Low Frequency and High Frequency Speaker EQHeadphone Output with Volume ControlMonitor Mute ControlRMC On/Bypass ControlAdjustable input gain with Signal Present and Clip indicatorCan be used with any studio monitor systemInputs A, B / C: 4 Balanced 1/4" TRS, 2 Unbalanced RCAOutputs A, B and Subwoofer: 5 Balanced 1/4" TRSHeadphone: Stereo 1/4"RMC Mic In/Out: 1/8" TRSComputer Interface: USB 2.0Windows and Mac compatibleJBL's RMC

The desk arm is designed with cable management to provide neat desk space. The monitor mount is ideal for classrooms, offices, homes, public area, industrial settings, production line and many more. This LCD desktop mount renders maneuverability, flexibility and a chic look that is sure to flatter your monitor. The multi monitor mount boasts integrated strength through the latest engineering technology, and is tested for durability in our offshore manufacturing plant. The Cotytech monitor arm has been built with the end user in mind, and features easy installation while offering intuitive, practical and functional design from one of the leading manufacturers of monitor mounts. Features: Available in Clamp or Grommet bases Construction: Solid aluminum alloy Adjustable height varies by 12.8" at monitor end Clean look with minimal hardware visible from underside of work surface Quick release fastener Supports two LCD monitors up to 27" Tilt: -30° / 30° Swivel: Max 130° Height adjustments: 9.8" Rotation: 360° (po

Lennox, Armstrong, Baso Pulse Furnace, Spark Ignition Module Replacement

Improve your critical thinking skills in just a minute! Exercises will strengthen and sharpen the top of your class with word problems, verbal classifications, diagrams and other riddles, puzzles and teasers. Great for extra-credit or as time fillers in class and on the go. 45 reproducible pages, answers included. For grades 6-8.

The Behringer Behritone C50A 30W active full-range reference studio monitor gives you the ability to hear what your mixes will sound like on bass-challenged real-world systems such as computers, televisions, car stereos, and iPod docking stations. The C50A is 6-1/2" tall, and each contains a 5-1/4" speaker that provides excellent sound reproduction for great reference mixing. The cabinets are shielded, so you can place them next to computer monitors. For making high-quality, accurate mixes that sound great on any system, use the Behringer Behritone C50A to complete your monitor setup.Behringer Behritone C50A Features at a Glance:Vintage-style monitor cube modeled after the (in)famous model from the 70'sAccurate built-in 30-Watt Class-D amplifier optimally matched to the driverFull-range 5 1/4" driver with special diaphragm and deformation-resistant chassisHomogeneous dispersion pattern due to singular small-diaphragm full-range driver configurationMagnetic shielding allows placement near computer monitors6 1/2" cube cabinet with multiple coats of high-gloss piano lacquer finishPrecision-milled, high-rigidity MDF cabinet and baffle for minimal resonance5/8" microphone stand mount built into the cabinet base1/4" soft neoprene pad to serve as an acoustic isolatorBalanced XLR, 1/4" TRS and RCA input connectors plus gain control for precise calibrationHigh-quality components and exceptionally rugged construction ensure long lifeGet a real-world reference with the Behringer Behritone C50A!

Sold As a Pair... The flagship BX6 offers the fluid neutrality of the BX5 but brings the scale of its larger 2 1/2 way system into play. This potent configuration of twin 165mm (6 1/2") C-CAM® bass drivers single 165mm (6 1/2") C-CAM® mid-bass driver and 25mm (1") C-CAM® tweeter adds effortless authority to a long list of BX range virtues. The drivers work in tandem with a rigid multi-chamber structure to reveal greater muscularity and refinement in music and film sound. Still the BX6 retains the elegant room-friendly proportions of the BX5 - its deceptively compact cabinet finished in any of the beautiful BX vinyl wood finishes will enhance the look of any environment. New C-CAM® tweeter has greater sensitivity and a wider bandwidth beyond 30kHz. New C-CAM® bass and mid-range drivers refined by FEA analysis. Single bolt-through drivers. A design feature which means the driver is not fixed to the front baffle and cannot transmit vibrations and therefore colouration to the cabinet. Improved cabinet rigidity and stability. HiVe®II port technology to speed the transit of air from the cabinet resulting in more dynamic bass. High-quality terminal panels blend easy access with high-end functionality. Choice of four high quality vinyl wood finishes

Vacuum Pump, R134a Manifold Gauge Set, Electronic Scale & Installer Assortment "Brand New In Original Factory Package 1 Year Warranty" No. FJC-9287 Vacuum Pump, R134a Manifold Gauge Set, Electronic Scale & Installer Assortment Kit Includes: 1 Part # 2734 R134a Oil Injector 1 Part # 2740 Fin Straightening Comb 1 Part # 2744 Large valve Core Remover Tool 1 Part # 2745 Small valve Core Remover Tool 1 Part # 2792 1 Dial Thermometer 1 Part # 2850 Pro-Charge Electronic Refrigerant Charging Scale 1 Part # 2882 Ford Spring Lock Coupler - 3/8 Red 1 Part # 2883 Ford Spring Lock Coupler ½ Blue 1 Part # 2884 Ford Spring Lock Coupler 5/8 Black 1 Part # 2885 Ford Spring Lock Coupler ¾ White 10 Part # 4008 O-Ring #8 1 Part # 4278 O-Ring Assortment 1 Part # 6014 R134a Adapters, 1/4" Flare Female X 1/2" ACME Male 1 Part # 6015 Adapter- 1/2 ACME female to 1/4 male 1 Part # 6016 R134a Tank Adapter 2 Part # 6017 R134a Hose Connector 2 Part # 6018 R134a Adapter, 14m X 1.5 X 1/4" Flare 1 Part # 6019 Adapter - 1/2 ACME m

"TR1 roughly doubles the size of the C++ standard library, and it introduces many new facilities and even new kinds of library components. TR1 has some classes, for example, where some nested types may or may not exist depending on the template arguments. To programmers whose experience stops with the standard library, this is strange and unfamiliar. This book is complete (it covers all TR1 facilities), it is easier to understand than TR1 itself, and it is technically accurate." --Matthew Austern, software engineer, Google"TR1 will help make the C++ programmer more productive than ever. In this book, Pete Becker has written the ultimate reference guide to these components, what they are, how they work, and what they're used for. This book should be on the bookshelf of anyone who wants to use these standardized components to improve both their productivity as well as their coding quality." --John Maddock, consultant and programmer The current C++ standard library extends the core C++ language with common classes and functions. In recent years, to address limitations in that library, a number of components have been developed to extend the language even further. Compiled in a comprehensive technical report (TR1), the bulk of these extensions have been approved for the next revision of the C++ standard. In this book, Pete Becker describes in detail each component in the TR1 library, explaining new facilities for utilities, containers, call wrappers, type traits, numerics, regular expressions, and C compatibility. He draws on his own experience implementing these components to illustrate their value, clarifying the specifications when necessary and providing complete, tested code examples. Most chapters include exercises of various degrees of difficulty to help programmers get hands-on practice with the new components. Answers to the exercises, along with all code examples, are available on the Web. Appendixes comprise a summary of headers included in or extended by the TR1 library, as well as guidelines on how to use the components safely in multithreaded applications.The C++ Standard Library Extensions is for any programmer who wants to get a jump on the revised standard. It also makes the perfect companion to The C++ Standard Library, by Nicolai Josuttis, both books being tutorials and references essential for using C++ more effectively.

WOCA Heavy Solid Master Oil - White with a solid matter content of approximately 91% and is used with a floor machine(Formerly Trip Trap) may be used on all unfininshed, freshly sanded and newly laid wood floors in all wood species. To be used on untreated and lye primed wood such as interior wood floors, wood stairs, wood panels, and wood furniture. The WOCA Master Oil has excellent penetration properties and therefore ensures a hard-wearing, dirt and water resistant surface. The WOCA Master Oil Natural is mainly used on dark wood species and enhances the natural warm glow of the wood whereas light wood species are often finished with WOCA Master Oil White which maintains and protects the natural light colour.Coverage: 1 liter of oil for every 120 to 180 sq. ft. depending on the wood species.Preparation:The unfinished wood should be freshly sanded with grit 100-120. Clean the floor with WOCA Wood Cleaner mixed with 2 gallons of warm water + 6.4 oz. (just over 3/4 cup) of Wood Cleaner. Use the high quality WOCA Swep Mop, which has no loose ends. The wood floor must be completely dry and free from dirt and grease before the WOCA oil application. Recommended moisture maximum 12%. The oiling is made at minimum 18 degree C.Base Coat Work Instruction:* Shake WOCA Oil container well before and during use. Choose your starting area and pour oil into a paint tray. Apply the Master Oil with a (short-haired) 3/8" nap paint roller and extension pole. Roll the oil as if you are painting the floor. Continue to spread oil until you coat 200-250 sq. ft.. Let the oil sit for 5-10 minutes. This will allow the wood floor to absorb oil into the open pores. During this period, move oil around in the treated area as you notice dry spots. When finished, rest your roller in the paint tray or on the cardboard.? With a red 3M (or similar colorfast) pad under a 175 rpm buffer, wet buff the oiled area slowly for several minutes. This continues to force oil into open pores. Buff until floor is completely saturated with oil, which means that some excess oil must be visible on the surface when finished. Shut off the buffer in the wet area, remove the wet pad and place it on a piece of cardboard.? With a squeegee, pull all of the oil off of the treated area and onto the next work area. Walk over the oiled floor and with lint free rags wipe up any standing oil. Wipe along walls, corners and door frames, even if no oil residue is visible. If you have beveled planks or cracks between planks, wipe these also if you see excess oil. To speed up removal of excess oil, consider placing a WOCA Polishing Cloth under a clean pad and use the buffer to remove any residue.? Place a white 3M (or similar) pad under the buffer. Immediately after removing excess oil from the work area, polish the oiled floor. Make at least two slow passes over the area. Wipe up any oil spots that you see while polishing. When finished, the oiled area should have a silky appearance and no oil residue on top of the floor. If you walk on the oiled area after polishing, buff away your foot prints.? Repeat the process until the floor is completed. After finishing a room, inspect the floor carefully. If necessary, polish the entire floor once more with a clean white pad.? When using Master Oil Natural or White, allow the oil to pre-harden (dry enough to walk on without leaving foot prints ) for 5 to 6 hours before applying the top coat. When using Color Oil allow 5 to 6 hours when top coating with the same Color Oil or 20 to 24 hours when topcoating with Maintenance Oil Paste. High humidity and cool temperatures may increase the drying time.+To prevent ?bleed back?, wipe up oil between floor boards with gaps or bevels before polishing with the white pad.+If you must quit the oiling process, pick a logical place to stop. Tape off adjoining planks if necessary before oiling and wipe up any oil that may get on bare wood or you will get a ?shiny? spot when you continue the oiling. Never stop in the mi

The A1-CT Showerhead is Sprite Industries' Original All-In-One. With a high-flow filter (the A1C) and high strength housing, the A1-CT is one of the strongest, most durable showerheads anyone offers. The elegant triple plated finish will not chip and will keep your shower looking fresh and decorative for a lifetime. THE ORIGINAL ALL-IN-ONE COMBINES FILTRATION AND STYLE INTO A MULTI-FUNCTIONAL FILTERING SHOWERHEAD THAT ALSO INCLUDES A THREE-WAY MASSAGING SPRAY! For relief from a stressful day, or sore, tense muscles after difficult work, the A1-CT offers a calming massage spray that does more than just clean. A Sprite showerhead brings all the best qualities a showerhead and a filter should have and combines these together for an overall second-to-none appliance. Don't forget that the filter of the A1-CT will completely remove chlorine and all impurities from the water to bring softer skin and healthier hair. With patented Chlorgon technology no traces of hydrogen sulfide or iron oxide will linger in your water either. All that will ever touch your skin is pure, fresh water reaching you in the form of a massaging stream! Try the original All-In-One A1-CT Sprite Showerhead to experience the cleanest shower for yourself!

Graceful curve design makes product compact and easy to carry. High compatibility charges iPhone MP3 MP4 and other digital devices. Lamp SpecificationsSpecDataWarranty1 Year Also Know As: HCC601A HC-C60-1A HC-C601A HCC60-1A HCC60-1AWhite HCC60-1A-White HC-C60-1AWhite Works With The Following Models: iPod iPhone and Smart Phones.

C.A.P. OZN-1 Ozone Generator (OZN-1) C.A.P. OZN-1 OZONE GENERATOR The C.A.P. OZN-1 Ozone Generator attacks and neutralizes odors at the source. Eliminates odors caused by smoke mold mildew pets cooking and damp basements by generating ozone (03) one of the most powerful oxidizers available. O3 doesn t just mask odors it neutralizes odors at the source then converts to CO2 and oxygen. Built in mounting brackets make for easy installation. Comes complete with a 3 year no hassle warranty (6 months on the bulb). Good for deodorizing up to 5500 cubic feet. Produces up to 1 000 mg of ozone per hour. Manufacturer s Product Information 2007 MSRP Each $ 179.95 Unit Weight 6 Case Dimensions 13 1/16 x 11 7/8 x 30 3/8

Lennox, Armstrong, Baso Pulse Furnace, Spark Ignition Module Replacement

By Adam Gorb (1958-). For Concert Band (1st Flute, 2nd Flute, Oboe, 1st Bb Clarinet, 2nd Bb Clarinet, 3rd Bb Clarinet, Bb Bass Clarinet, Bassoon, 1st/2nd Eb Alto Saxophone, Tenor Saxophone, Baritone Saxophone, 1st/2nd Bb Trumpet, 1st/2nd F Horn, 1st/2nd Trombone, Euphonium, TC Baritone, Tuba, P). Band Music. Grade 3. Score and parts. Duration 4:30. Published by C. Alan Publications

This is a brand new Copeland brand scroll compressor, Model # Z48K5-PFV This is a 230 volt/ 1 phase/ R-22 /4 ton A/C compressor that works on most all residential and light commercial applications. This can replace many 3 ton models. The compressor uses a rotary scroll, instead of old-fashioned reed valves, for a more reliable compressor. These compressors have a 1 year warrenty Comes with a matching capacitor for a complete replacement SHOULD I BUY FROM A SURPLUS SELLER, OR HERE WITH AC MIKE?

Manhattan HD071A2 7.1" HD Professional LCD Monitor with Canon Plate #HD071A2-C SKU: MHD071A2C Mfr. Part: HD071A2-C Manhattan HD071A2 7.1" HD Professional LCD Monitor with Canon Plate, 1024x600 WXGA Resolution, 400 Nits Brightness, 500:1 Contrast Ratio Manhattan HD071A2-C 7.1" HD Professional LCD Monitor - Canon Plate - Manhattan 1 Year Warranty The Manhattan HD071A2-C 7.1" HD Professional LCD Monitor with Canon Plate is designed for field monitoring. This wide screen LCD monitor is full HD compatible with multiple inputs. This monitor has the more advanced Pixelworks chipset it has features such as an Advanced Color Control, True Anamorphic 16:9 aspect ratio, 1:1 Pixel Mapping & is also firmware upgradeable. The panel is 1024 X 600 resolution, matte finish great for outdoors. LCD Size 7.1" Contrast ratio 500:1 Brightness 400 Nits Response Time 25 ms, full on/full off Viewing Angle (L/R/U/D) 140 / 110 degrees Controls Brightness - Contrast - Saturation - Red Green Blue Channel Levels Fit All - 1:1 (Pixel Mappi

.style1 { border-collapse: separate; border-left: 0px none #C0C0C0; border-right: 0px none #A0A0A0; border-top: 0px none #C0C0C0; border-bottom: 0px none #A0A0A0; } .style2 { border-width: 0px; } .style3 { border: 1px solid #CCCCCC; } Top Seller! The Big Men's Pro Cycling Shorts by Aero Tech Designs is a padded bicycle short with an eight-panel anatomical design. There are no seams between the legs, so the smooth inner leg reduces opportunity for abrasion and saddle sores. This cycling short is a proven performer with many loyal fans. You will love these bike shorts. Ideal for anti-abrasion. ATD Fabricham Crotch Pad is Not so thick. Our men's cycling apparel means comfort. The men's bike short has the Multi Layer Pad (MLP) design with smooth edges that wrap the body curves between the legs. The fabricham surface is a smooth, antibacterial hygienic microfiber, that is laminated to foam and tricot. It is extremely breathable, lightweight and stays dry to inhibit the growth of bacteria. This is the most breathable, most comfortable pad you will ever wear for your bike rides! It is a Proven Performer. This padded bike short is tested, guaranteed to add comfort. Bike Shorts are to be worn without underwear with the crotch pad tight to the skin. Chamois pad is breathable, the center is 7mm thick and sides 5mm thick The pad is just the right thickness for experienced riders. It is not one of those heavy diaper type pads. We offer a better fit than you have ever experienced. The crotch pad is full cut with a seamless center of soft antibacterial microfiber that will not bunch up. The entire pad has a tricot under layer to wick moisture and keep you dry. Dries Instantly - Lightweight. Hygienic® is a permanent finish which prevents premature fabric decay and prevents the growth of bacteria and odors so giving a healthy micro climate between the body and fabric which is ideal for bike short * Pad thickness is 7mm in center and 5mm on sides. * Chamois pad prevents abrasion and absorbs shock, it is not so thick * Ideal for anti chafe and freedom of movement. * Men's Bicycle Shorts add compression for comfort on bike rides. * Compression from the spandex against your muscles supports blood flow * The spandex increases blood flow. * Cross Grain Cutting maximizes stretch performance of spandex fabric * Shorts bupport bicycle rides and hold the flesh to maximize performance. * 8-panel construction is designed with curves for cycling * Smooth inner leg reduces opportunity for abrasion and saddle sores. * Fabric is four way, 7.4 oz, nylon/lycra, tricot knit - THE BEST! * Bike short has Leg grippers that are very smooth, sized just right * No seams between the legs. Waist elastic is soft * Colors: Black, Red Bike Shorts, Navy Bike Shorts, Royal Blue Shorts * Unconditional Guarantee - Very High Quality Men's Pro Bike Shorts XS Small Medium Large XL 2XL 3XL 4XL 5XL Men's Waist 22-26 28-30 32-34 36 38-40 42-44 46-48 50-52 54-56 Inseam (inches) 8 1/4 8 1/2 8 3/4 9 1/4 9 1/2 9 1/2 9 5/8 9 3/4 9 3/4 Leg Hems (gripper inside) - The leg grippers keep crotch area smooth by preventing bunching up at the crotch area. Silicone elastic is easy to wear and very soft. Waist Elastic - The waist is a soft, 3/4 inch elastic that is cover stitched for stretch-ability.

The ALS1 line splitter seperates the two 120VAC current carrying wires, enabling the user to easily measure current with any AC current clamp meter.

Bugatti presents a world of new emotions and feelings, a world of extraordinary creativity. Our aim is to follow a natural evolution linking practical aspects to a modern lifestyle. Relying on an internationally known brand name is not enough, the quality, beauty and practicality of each item is vital: the Italian style. Casa Bugatti wants to change the way you think about your tabletop and kitchen. We take a basic and regularly used item, revalue and modify it, so that we can present you with a new concept, helping to make the culture of buying tableware and gifts a new world for you to discover. Enjoy yourself! Uniquely artful bowl held aloft by a woman in a white dress holding the bowl over her head. Great for fruit, pot pourri or other items around your home.

This is a brand new, sealed, in box, Copeland brand scroll compressor, Model # ZP54K3E-PFV This is a 230 volt/ 1 phase/ R410A / 5 ton A/C compressor Works on most all residential and light commercial R 410A central air condensing units. This can replace many 4 ton models. The compressor uses a rotary scroll, instead of old-fashioned reed valves, for a more reliable compressor. These compressors have a 1 year warranty Comes with a run capacitor for a complete replacement. PLEASE NOTE- THIS COMPRESSOR IS FOR R410A SYSTEMS ONLY DO NOT DROP IN AN R 410A COMPRESSOR IN AN OLDER R-22 SYSTEM SHOULD I BUY FROM A SURPLUS SELLER, OR HERE WITH AC MIKE?

American Lifeguard Products JR. Guard Cap The Deluxe JR. Life Guard Baseball Cap with 3-D High Definition Embroidery. Lifeguard letters measure 1 1/2" inch tall & 5" inch wide. The bill 7 1/4" inch wide & 2 7/8" deep. Bill wrapped with Life Guard screen print. Color: Navy Material: Acrylic Adjustable Fit, Closure 2 inch Velcro Design 3-D High Definition Embroidery One size fit all This is a great looking Cap and it has a really solid bill that won't get easily bent out of shape. The quality is really good the material is pleasant to the touch. Its very affordable and is a very popular item.

WOCA Heavy Solid Master Oil - Natural with a solid matter content of approximately 91% and is used with a floor machine(Formerly Trip Trap) may be used on all unfininshed, freshly sanded and newly laid wood floors in all wood species. To be used on untreated and lye primed wood such as interior wood floors, wood stairs, wood panels, and wood furniture. The WOCA Master Oil has excellent penetration properties and therefore ensures a hard-wearing, dirt and water resistant surface. The WOCA Master Oil Natural is mainly used on dark wood species and enhances the natural warm glow of the wood whereas light wood species are often finished with WOCA Master Oil White which maintains and protects the natural light colour.Coverage: 1 liter of oil for every 120 to 180 sq. ft. depending on the wood species.Preparation:The unfinished wood should be freshly sanded with grit 100-120. Clean the floor with WOCA Wood Cleaner mixed with 2 gallons of warm water + 6.4 oz. (just over 3/4 cup) of Wood Cleaner. Use the high quality WOCA Swep Mop, which has no loose ends. The wood floor must be completely dry and free from dirt and grease before the WOCA oil application. Recommended moisture maximum 12%. The oiling is made at minimum 18 degree C.Base Coat Work Instruction:* Shake WOCA Oil container well before and during use. Choose your starting area and pour oil into a paint tray. Apply the Master Oil with a (short-haired) 3/8" nap paint roller and extension pole. Roll the oil as if you are painting the floor. Continue to spread oil until you coat 200-250 sq. ft.. Let the oil sit for 5-10 minutes. This will allow the wood floor to absorb oil into the open pores. During this period, move oil around in the treated area as you notice dry spots. When finished, rest your roller in the paint tray or on the cardboard.? With a red 3M (or similar colorfast) pad under a 175 rpm buffer, wet buff the oiled area slowly for several minutes. This continues to force oil into open pores. Buff until floor is completely saturated with oil, which means that some excess oil must be visible on the surface when finished. Shut off the buffer in the wet area, remove the wet pad and place it on a piece of cardboard. ? With a squeegee, pull all of the oil off of the treated area and onto the next work area. Walk over the oiled floor and with lint free rags wipe up any standing oil. Wipe along walls, corners and door frames, even if no oil residue is visible. If you have beveled planks or cracks between planks, wipe these also if you see excess oil. To speed up removal of excess oil, consider placing a WOCA Polishing Cloth under a clean pad and use the buffer to remove any residue. ? Place a white 3M (or similar) pad under the buffer. Immediately after removing excess oil from the work area, polish the oiled floor. Make at least two slow passes over the area. Wipe up any oil spots that you see while polishing. When finished, the oiled area should have a silky appearance and no oil residue on top of the floor. If you walk on the oiled area after polishing, buff away your foot prints. ? Repeat the process until the floor is completed. After finishing a room, inspect the floor carefully. If necessary, polish the entire floor once more with a clean white pad. ? When using Master Oil Natural or White, allow the oil to pre-harden (dry enough to walk on without leaving foot prints ) for 5 to 6 hours before applying the top coat. When using Color Oil allow 5 to 6 hours when top coating with the same Color Oil or 20 to 24 hours when topcoating with Maintenance Oil Paste. High humidity and cool temperatures may increase the drying time. +To prevent ?bleed back?, wipe up oil between floor boards with gaps or bevels before polishing with the white pad. +If you must quit the oiling process, pick a logical place to stop. Tape off adjoining planks if necessary before oiling and wipe up any oil that may get on bare wood or you will get a ?shiny? spot when you continue the oiling. Never stop i

When you're performing live, it can be a pain switching instruments if you don't have a Lehle 3at1 SGoS instrument switcher. It's not convenient to constantly switch cables, and no one wants to hear pops, clicks, and hum while you do it. It doesn't matter if you play acoustic-electric guitar, bass, or even keyboards - the 3at1 SGoS handles any instrument- or line-level input with ease, and lets you switch between them silently. Even better, channels A and B have adjustments to help them match the signal level on the C channel for consistency. And each channel is stereo, so it's easy to integrate keyboards and stereo effects processors. Factor in MIDI programmability, and the ability to network with other Lehle switchers, and you've got a truly professional switching solution in the Lehle 3at1 SGoS instrument switcher.Lehle 3at1 SGoS Instrument Switcher at a Glance:Inaudible instrument switchingMix and match instruments and sourcesProfessional switching capabilitiesInaudible instrument switchingThe whole point of the Lehle 3at1 SGoS instrument switcher is that your audience shouldn't know you're switching instruments without seeing you do it. That means no pops, no clicks, no hum while you grab your next instrument. Just leave them all connected to the Lehle 3at1 SGoS, and it'll take care of the switching silently and reliably. How? Gold-plated relay switches with pop/click suppression - professional grade circuitry for serious performance.Mix and match instruments and sourcesYou may have found the Lehle 3at1 SGoS looking for a solution for your guitars or basses, but it can handle virtually any instrument with ease. Acoustics with piezo pickups, passive or active pickups, even line level sources are accommodated by the 3at1 SGoS. And inputs A and B have gain adjustments, so you can balance all connected instruments and sources relative to input C.Professional switching capabilitiesThe Lehle 3at1 SGoS fits into even the most complicated stage rigs, and can be programmed via MIDI for even more flexibility. You can also network the 3at1 SGoS with other Lehle switchers for convenience. With so many ways to use the Lehle 3at1 SGoS, call your Sweetwater Sales Engineer to see how the 3at1 SGoS will work with your gear.Lehle 3at1 SGoS Instrument Switcher Features:Silent switching for up to three instrumentsVersatile inputs handle electric instruments, piezo pickups, and line-level sourcesGold-plated relay switching and pop/click suppression provide sonically transparent performanceStereo signal path makes it ideal for keyboard switching, and stereo effects processorsProgrammable via MIDI for configurable functionalitySwitch between instruments like a pro with the Lehle 3at1 SGoS instrument switcher!

A/C Re-New A/C Re-New is an exciting, new branding of Zerol Ice for residential air conditioning systems. Quiets noisy compressors. Reduces energy consumption. Improves heat transfer in the evaporator and condenser. Great for new and old systems. Zerol Ice has established an outstanding track record enhancing the performance of air conditioning and refrigeration systems. Now we have the same formula re-branded as A/C Re-New for residential air conditioning systems. Residential air conditioning systems account for up to 70% of the home's energy consumption. And when the outdoor temperature rises the system works longer and harder. Through tests on actual installations, the A/C Re-New technologyhas demonstrated its ability to reduce the air conditioning systems energy use on average by 11% It has also been found to improve the system's cooling performance and quiet noisy systems.

The Behringer C-1 Studio Condenser Microphone large diaphragm condenser microphone is probably one of the best values you'll find in a condenser mic. This is a great all-around studio recording mic, ideal for capturing vocals and instruments in the studio. It also excels in live applications. The pressure-gradient transducer with its shock-mounted capsule produces a smooth, flat frequency response. You get a rugged, die-cast metal chassis, gold-plated XLR connector, a swivel stand mount, and foam-padded carrying case. You can't go wrong with the Behringer C-1.Behringer C-1 Studio Condenser Microphone Features at a Glance:Ideal as main and support microphone for studio and live applicationsCardioid pickup pattern for outstanding sound source separation and feedback rejectionPressure-gradient transducer with shock-mounted capsuleUltra-low noise, transformerless FET input eliminates low-frequency distortionLED indicates phantom power operationSwivel stand mount and transport case includedUltra-rugged construction with metal die-cast bodyGold-plated 3-pin XLR output connector for highest signal integrityHigh-quality components and exceptionally rugged construction ensure long lifePick up a Behringer C-1 Studio Condenser Mic (or two)!