Air Conditioner Accessories

The 50A65-843 is a Universal Silicon Nitride (Hot Surface) Ignition Control With Variable Timings. Replaces 50A65-120, -143, -288, -474, -475 And More. The 50A65-843 Universal Nitride Integrated Ignition module is an automatic ignition control that employs a microprocessor that continually monitors, analyzes, and controls the proper operation of the gas burner, inducer, and fan. The 50A65-843 is unique because it incorporates our patented adaptive algorithm routine that uses an 80V nitride ignitor to ensure the most effective ignitor temperature, increasing the life expectancy of the ignitor. This one module will replace all of the 50A65-XXX integrated ignition nitride modules that have been manufactured by White-Rodgers. The Universal Module has an extensive cross reference for replacement and includes additional jumper wires, additional wiring harness, a jumper for Trane applications and a 3/16 terminal for Lennox (only). The module also has terminals for powering a humidifier and an air cleaner.

This is a BRAND NEW OEM Carrier/Bryant Furance Control Circuit Board. The Carrier/Bryant/Payne Part # is LH33WP002A. Honeywell #s are 1068-12 1068-83-129A. Thanks for looking and good luck! Visit My eBay Store: NorthAmericaHVAC **Express Mail only ships Mon-Fri!! Partial List of Carrier / Bryant Units that use this Board: 48A2020110669 48A2020610669 48A2025110669 48A2025610669 48A2027110669 48A2027610669 48A2030110669 48A2030610669 48A2035110669 48A2035610669 48A2040110669 48A2040610669 48A2050

The 780 Series Hot Surface Ignition Modules are designed for use on gas fired heating systems. The system acts on a demand for heat by a switch or thermostat to supply power to the ignition control. On non pre-purge models, the ignitor will be energized immediately and remain on for either of two optional selected ignitor heat-up times approximately 17 or 34 seconds. For models with the prepurge option, there is a time delay equal to the heat-up time selected before the ignitor is energized. At the end of the ignitor heat-up time the gas valve is opened supplying gas to the main burner. After several seconds, the ignitor is turned off and the sensor is energized. As long as flame is sensed, the system continues to operate. When the thermostat is satisfied, the gas control will be closed to shut off the main burner. The 780 Series provides lockout and complete gas shut off if ignition is not proven after the trial for ignition sequences has been completed.

Honeywell model S8610U3009 Universal Intermittent gas module control For Single Or Dual Rod Flame Sensing With Vent Damper Plug. For use on Natural or LP Gas. 90 Sec Trial For Ignition. 5 Min Shutoff. Continuous Retry. 100% Shutoff. Provides ignition sequence, flame monitoring and safety shutoff for intermittent pilot central furnaces and heating appliances. Provides 100 percent pilot gas shutoff if pilot fails to light; after 6-minute delay, trial for ignition is repeated. Ignition trial/delay sequence is repeated until the appliance lights or call for heat is removed. Functional equivalent of S86, S8600, S8610 and S90 modules. New model replacement for older S8610U1003 which is now obsolete.

Universal Replacement Intermittent Pilot Module Honeywell part number: S8610U3009 Provides electronic control of most intermittent pilot ignition systems used on gas-fired furnaces, boilers, and other heating appliances. Features: Provides shutoff if pilot fails to light; after 6-minute delay a trial ignition is repeated. Ignition trial sequence is repeated until the appliance lights or call for heat is removed. For use with Natural or LP gas For use in single rod or dual rod/remote sense appli

You will receive a Honeywell S8610U3009 which is the direct replacement for S8600H, S8600M, S8610A, and S8610B One or Two Rod Intermittent Pilot Control with continuous retry trial time with configurable lockout timing of 15 or 90 seconds and configurable prepurge of 30 seconds or no prepurge Provides ignition sequence, flame monitoring and safety shutoff for intermittent pilot central furnaces and heating appliances. Provides 100 percent pilot gas shutoff if pilot fails to light; after 6

Manufacturer: Honeywell International Model: S8610U 3009 Description: Universal Replacement Intermittent Pilot Module. specs:S8610U3009 One or Two Rod Intermittent Pilot Control with continuous retry trial time with configurable lockout timing of 15 or 90 seconds and configurable prepurge of 30 seconds or no prepurge Overview Field service replacement for most Honeywell, Robertshaw, Johnson, and UTEC (HSC) Intermittent Pilot Ignition Modules. Provides electronic control of most intermittent pilot ignition systems used on gas-fired furnaces, boilers, and other heating appliances. Features Provides ignition sequence, flame monitoring and safety shutoff for intermittent pilot central furnaces and heating appliances. Provides 100 percent pilot gas shutoff if pilot fails to light; after 6-minute delay, trial for ignition is repeated. Ignition trial/delay sequence is repeated until the appliance lights or call for heat is removed. For use with Natural or LP gas. For use in single rod or dual rod/remote sens

Honeywell model S8610U3009 Universal Intermittent gas module control For Single Or Dual Rod Flame Sensing With Vent Damper Plug. For use on Natural or LP Gas. 90 Sec Trial For Ignition. 5 Min Shutoff. Continuous Retry. 100% Shutoff. Provides ignition sequence, flame monitoring and safety shutoff for intermittent pilot central furnaces and heating appliances. Provides 100 percent pilot gas shutoff if pilot fails to light; after 6-minute delay, trial for ignition is repeated. Ignition trial/delay sequence is repeated until the appliance lights or call for heat is removed. Functional equivalent of S86, S8600, S8610 and S90 modules. New model replacement for older S8610U1003 which is now obsolete.

Overview Field service replacement for most Honeywell, Robertshaw, Johnson, and UTEC (HSC) Intermittent Pilot Ignition Modules.Provides electronic control of most intermittent pilot ignition systems used on gas-fired furnaces, boilers, and other heating appliances.Features Provides ignition sequence, flame monitoring and safety shutoff for intermittent pilot central furnaces and heating appliances.Provides 100 percent pilot gas shutoff if pilot fails to light; after 6-minute delay, trial

HONEYWELL S8610U3009 Intermittent Pilot Ignition Modules (S8610U-3009, S8610U 3009) REPLACES OBSOLETED S8610U1003 OVERVIEW Field service replacement for most Honeywell, Robertshaw, Johnson, and UTEC (HSC) Intermittent Pilot Ignition Modules. Provides electronic control of most intermittent pilot ignitionsystems used on gas-fired furnaces, boilers, and other heating appliances. Provides ignition sequence, flame monitoring and safety shutoff for intermittent pilot central furnaces and heating appliances. Provides 100 percent pilot gas shutoff if pilot fails to light; after 6-minute delay, trial for ignition is repeated. Ignition trial/delay sequence is repeated until the appliance lights or call for heat is removed. For use with Natural or LP gas. For use in single rod or dual rod/remote sense applications. Includes relay contacts for use with any intermittent pilot gas control string with maximum 1.0A pilot or 2.0A main valve rating; Honeywell VR8204, VR8304 or VR8345M combination gas control recommend

ICM283 GAS IGNITION CONTROL FEATURES AND APPLICATIONS Hot Surface Ignition (HSI) module Single/Dual rod sensing capabilities For gas fired furnaces, boiler and other heathing appliances Switch selectable lockout times, ignition trails Works both natural & LP gas systems Diagnostic LED to aid in troubleshooting REPLACES: HONEYWELL: S8910U-1000 ROBERTSHAW: HS780 WHITE RODGERS: 50E47, 50F47 SPECIFICATIONS: Input Voltage: 120 & 24 VAC, 60 Hz HSI: 120V, 5A maximum Valve: 24V, 2A maximum Total: 24V Load=0.4 + valve load Pre-purge time: 32 seconds Ignition Trials to lockout: 1 or 3 (switch selectable)

Honeywell S87B1016 Spark Ignition Module 11-Second Lockout Single Rod 25VAC 60Hz This ignition module provide electronic control of direct spark ignition systems used on gas fire furnaces, boilers, and other heating appliances. For use with any DSI valve. Features Control ignition sequence and gas control operation. Generate high voltage potential for main burner ignition. Lockout after one trial for ignition if main burner fails to ignite. Reset from thermostat after lockout. Use modules (except S87C) with any combination gas control designed for direct spark applications and rated 2.0A or less. Specifications Description: Provide electronic control of direct spark ignition systems used on gas fired furnaces, boilers, and other heating appliances. Ignition System Type: Direct Spark Ignition Ignition Sequence: Single trial for main burner ignition (then shut down and lockout) Typical Gas Control: VR8205, VR8305 Type of Gas: Natural or LP Ignition Source: Internal high voltage spark generator Prepurge: None Ig

One or Two Rod Intermittent Pilot Control with continuous retry trial time with configurable lockout timing of 15 or 90 seconds and configurable prepurge of 30 seconds or no prepurge Overview Field service replacement for most Honeywell, Robert Shaw , Johnson, and UTEC (HSC) Intermittent Pilot Ignition Modules. Provides electronic control of most intermittent pilot ignition systems used on gas-fired furnaces, boilers, and other heating appliances. Features Provides ignition sequence, flame m

ICM2805 Miller Nordyne 903106 Furnace Control Board ICM2805 Furnace Ignition Control Module Features: Low cost form, fit and functional OEM replacement control board for Nordyne: 903106-Kit For use with G3, G4, G5, G6, M2 and M3 furnace modules Controls gas valve, inducer draft motor, circulating blower and hot surface ignitor Monitors timing, trial for ignition, flame sensing, lockout, plus pressure, rollout and limit switches Microprocessor-based precision Twinning compatible with another ICM2805 furnace control Diagnostic LEDs aid in testing and troubleshooting Specifications: Specifications Voltage Range: Line (98 to 132 VAC) @ 60 Hz Ignitor: 5A, 120 VAC Cool Blower: 10A, 2HP, 240 VAC Heat: 5A, 1/2 HP, 250 VAC Inducer Blower: 4A, 120 VAC Gas Valve: 1A, 24 VAC Humidifier Motor: 0.5A, 24 VAC Electronic Air Cleaner: 1A, 120 VAC Replaces: 624591-A, 624591-B, 624591-C, 624591-D, 624631-A, JHL, 6245640, 624631-A, 6245910 and others.