F00158 5X Hook & Loop Fastening Tape,Helicopter,Others

Zinc plated 5/8 x 6 . Lag screws are easy you install and provide excellent support. Screw hook for all 1-5/8 gates. Easy to install.

Can be used as a clothesline hook or as a rope tie down. Zinc plated to resist rust. Bulk hook bolts are supplied with hex nuts assembled.

Brainerd 5/16 By 4 Inch Galvanized Swing Hook (3) 2-PACKS 3 SETS OF GALVANIZED SWING HOOKS !!!Swing hooks with bearings mechanically galvanized - card of 2 size ins.=5/16 x 4 Designed exclusively to replace original swing equipment or new construction Includes nylon bearing for smooth swing operation and long life Weathergard protection from outdoor elements Maximum rust protection for outdoor and high humidity areas Maximum load limit: 210 lbs.Product Details Length 5/16", 7.94mm Width 4", 101.6

Shop for Hardware & Fasteners at The Home Depot. Get the Crown Bolt 8-Piece Mr. Grip Screw Hole Repair Kit to replace worn threads and fix screw holes. This kit is suitable for use with a variety of wood, metal and plastic items.

Hooks, This hook is designed for use as a replacement part with Fastenals #290 Screw Hook and Strap Hinges or for new installations with Fastenals #294 Hinge Strap Only. Hook adjusts to correct gate sag Adjusts to correct gate sag.

1/2" x 9 HOOK/HOOK TURNBUCKLE. Turnbuckles are rated with full thread engagement. Use caution to insure proper installation. Rated Capacity refers to a straight, zero degree, pull. Pulling at an angle can reduce the rated capacity significantly. Safety Factor equals 2.5 Rated Capacity. Meets specification FF-T-791b, Type 1, Form 1 Class 5. Open length estimated dependent on how far out of full thread engagement installation. Forged Carbon Steel. 1/2" X 9 TURNBUCKLE (HOOK/HOOK) Design: Hook / Hook Process: Forged Threads: UNC Material: Carbon Steel Finish: Hot Dip Galvanized Fitting Shank

*Includes 6 clamps: micro 46, SAE 12, 20, 28 & 36 Hand tighten the "Turn Key"hose clamp for a leak-proof seal, even in tight spaces For a tamper-resistant connection, pull off the turn key after tightening Stainless steel band and housing Fits 1/4" to 2-3/4" diameters, Weight: 1 lbs., Manufacturer: TRIDON INCORPORATED

Cooling Tower Motor, 3-phase, 1-1/2 Hp, Nameplate Rpm 1755, Voltage 200, Nema Frame 145t, Totally Enclosed Fan-cooled, Base Mounting, 60/50 Hz, Full Load Amps 4.65, Inverter Duty, Service Factor 1.25, Nominal Efficiency 86.5, Double-shielded Ball Bearings, Thermal Protection None, Cw/ccw Rotation, Insulation Class F, Max. Ambient Temp. 40 Degrees C, Shaft Dia. 7/8 In, Shaft Length 2-1/4 In, Cast-iron Frame Material

5/32" X 3-1/4" Zinc Hook & Eye Turn Buckle, 5pc NEW Description: 5/32" X 3-1/4" Zinc Hook & Eye Turn Buckles, 5pc You will receive 5! A turnbuckle is a device for adjusting the tension or length of ropes, and cables. It normally consists of two threaded eyelets, one screwed into each end of a small metal loop, one with a left-hand thread and the other with a right-hand thread. The tension can be adjusted by rotating the loop, which causes both eyelets to be screwed in or out simultaneously. Features: Hook and Eye Extruded aluminum body Zinc chromate steel eye and hook Turnbuckles are most commonly used in applications which tension is required. Inside Eye and Hook Diameter: 1/4 Screw Diameter: 5/32 Overall Closed Length: 3-1/4 Overall Fully Opened Length: 4-11/16"

Double engagement ('F' flex-flex) for parallel and angular misalignment Single engagement ('FFR' flex-rigid) accommodates angular misalignment only and is ideal for floating shaft applications Industry standard flange bolt patterns FHD Type standard for sizes 10 through 30 (other sizes available upon request)