Aircraft Fastener Screws Part # 202-15523C3-5 #10-32

11O7309 Up for sale is panel fastener for special applications this is covered under NSN 5305 01 420 7485 also part numbers CA-28080C08-9P also 845907-24 this has a 8-32 thread on the screw part and the knurled bushing has a internal thread that holds this onto the panel, this was shown to be a $32 unit cost each when we received them , buyer to pay calculated shipping and packing to your locations, see our store we have a lot of new items that came in, thank you RWK. 5305-01-420-7485 Character

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. Often used in aircraft fastening applications, drilled-head fasteners have a small hole drilled from one side of the head through to the other side - allowing lengths of wire to be used to prevent loosening on adjacent fasteners by wiring them together. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers. A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

12E151304 up for sale is a lot of 5 southco 260 turnlock panel fasteners, new from USA surplus, see additional data below, used on the f16 jet, buyer to pay calculated shipping and packing to your locations, see our store for more stuff like this, Thank you RWK. 5325-01-524-3360 ( 015243360, 5325015243360, 582R423H10, 82-11-260-16 ) Characteristics Data MRC Criteria Characteristic MATT MATERIAL STEEL COMP 1008 OR STEEL COMP 1009 OR STEEL COMP 1010 OR STEEL COMP 1012 OR STEEL COMP 1015 OR STEEL

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. Often used in aircraft fastening applications, drilled-head fasteners have a small hole drilled from one side of the head through to the other side - allowing lengths of wire to be used to prevent loosening on adjacent fasteners by wiring them together. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers. A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. Often used in aircraft fastening applications, drilled-head fasteners have a small hole drilled from one side of the head through to the other side - allowing lengths of wire to be used to prevent loosening on adjacent fasteners by wiring them together. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers. A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. Often used in aircraft fastening applications, drilled-head fasteners have a small hole drilled from one side of the head through to the other side - allowing lengths of wire to be used to prevent loosening on adjacent fasteners by wiring them together. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers. A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. Often used in aircraft fastening applications, drilled-head fasteners have a small hole drilled from one side of the head through to the other side - allowing lengths of wire to be used to prevent loosening on adjacent fasteners by wiring them together. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers. A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Fine threads are preferable when working with harder materials or when threading into a thin material. They are also stronger in tension than coarse threads, and generally provide higher shear strengths.

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. Often used in aircraft fastening applications, drilled-head fasteners have a small hole drilled from one side of the head through to the other side - allowing lengths of wire to be used to prevent loosening on adjacent fasteners by wiring them together. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers. A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. Often used in aircraft fastening applications, drilled-head fasteners have a small hole drilled from one side of the head through to the other side - allowing lengths of wire to be used to prevent loosening on adjacent fasteners by wiring them together. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers. A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.

Machine Screws, also referred to as Machine Bolts, are often used with nuts or driven into tapped holes. They come in a variety of head types and drive styles, but are generally available in smaller sizes.Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.    Fillister head fasteners are considered an improvement over round head equivalents - the smaller head creates more downward pressure for a given torque level and the thicker head plus deeper drive slot allows higher torque levels to be generated. Often used in aircraft fastening applications, drilled-head fasteners have a small hole drilled from one side of the head through to the other side - allowing lengths of wire to be used to prevent loosening on adjacent fasteners by wiring them together. Common applications for slotted screws include woodworking, although the drive style is not designed to be used with power drivers. A threaded fastener's size name includes information about the major external diameter, followed by the threads per inch, which indicates if it is coarse or fine. Coarse threads are better when working with brittle materials; they are sturdier and are easier to thread and unthread compared to fine. Coarse threading also allows for thicker coatings and platings.